Phone Mount Crossbar for Harley-Davidson Pan America
--- REQUIRES MADSTAD WINDSHIELD SYSTEM ---
This add-on accessory for the Madstad adjustable windshield system allows you to attach your phone where it MUCH easier to see, just below your line of sight. Instead of bobbing your head up and down to see your smartphone screen, you simply lower your gaze a few inches and there it is. Keep your eyes on the road, and your critical information front and center.
Note: Phone mount in photo not included.
The stainless steel bar brackets mount directly to the metal Madstad windshield system so you get the most solid mounting possible. The bar itself is solid 7/8" thick aluminum and will not rotate so that whatever you mount there stays in place. Mount up to two devices side-by-side, and you can use this crossbar whether or not you have purchased our Display Riser Kit.
Phone Mount Crossbar for Harley-Davidson Pan America
--- REQUIRES MADSTAD WINDSHIELD SYSTEM ---
This add-on accessory for the Madstad adjustable windshield system allows you to attach your phone where it MUCH easier to see, just below your line of sight. Instead of bobbing your head up and down to see your smartphone screen, you simply lower your gaze a few inches and there it is. Keep your eyes on the road, and your critical information front and center.
Note: Phone mount in photo not included.
The stainless steel bar brackets mount directly to the metal Madstad windshield system so you get the most solid mounting possible. The bar itself is solid 7/8" thick aluminum and will not rotate so that whatever you mount there stays in place. Mount up to two devices side-by-side, and you can use this crossbar whether or not you have purchased our Display Riser Kit.
THE MOST COMFORTABLE WIND PROTECTION A MOTORCYCLE CAN HAVE
G
Super easy to install and works fantastic! As a side note, I ordered my windshield too tall. I installed the windshield, and used some painter's tape to establish the correct height. I placed some poster board behind the windshield and traced the contours of the edge on the poster board. I covered the top several inches of the windshield with the painter's tape and used the poster board pattern to mark on the tape where I needed to cut it down. I then cut the windshield down using a Dremel with a 1 1/2" cut off wheel for plastic, sanded the cuts, and used a small torch to heat the edges. Ended up perfect. I took off about 2 1/4" - so the point is be careful to measure what size windshield you need to avoid the extra work above, but you can modify it if you have too.
R
This windshield is unbelievable better than others. My head used to Shake on the highway: not anymore!
J
I was a tiny bit confused with the install directions at first, then my brain slapped me and everything made sense. The install was actually rather simple and the end product was a very nice fly screen that moves just enough wind to make the ride that much more comfortable. Very happy with the product.
M
I wanted good wind control for highway use on my 2024 Bonneville T120. I tried another windshield, which honestly looked a little more retro and was a little less expensive, but it didn't work as well as I wanted. I'm 6'1" and have a tall torso, so I need something pretty tall. I purchased the Madstad 24 inch windshield with the lower deflectors. It was easy to install and is easy to remove. I appreciate the adjustability and was able to dial it in to eliminate the helmet buffeting that was present with the first windshield. I placed the top of the windshield at the level of the tip of my nose. I look over the windshield while riding and enjoy good wind protection. The windshield and hardware seem well designed and high quality.
M
I have a MadStad system on my 2009 V Strom and once you have it dialed in that's it no more adjusting. This is why I decided to go with MadStad again on my 2021 V Strom, the hole system takes about an hour to install and adjust for initial set up. Today is the first day I have ridden with the system and have already made two adjustments. So far so good. I'm not to fond of the frosting at the bottom of the windscreen, this is done to prevent the head light from reflecting on the screen. I haven't ridden at night, but when I started my bike in the garage the frosted area lit up white. I'm thinking of possibly painting the frosted area or applying some type of window tinting. Other than that I'm happy with the MadStad system and I'm sure it will get better once I go through the trial and error of fine tuning it for my riding style. As for giving three stars, let's just say in my case, MadStad had some issues with bracket quality control which set me installation back 10 days. I realize this is probably not the norm but in my case it was a reality.